TireFitLab

225/55 R16

What size is 225/55 R16?

225/55 R16 has an overall diameter of about 25.74 in, a section width of 8.86 in and a sidewall height of 4.87 in. It turns roughly 783 times per mile. Below are the exact figures plus plus/minus sizes that stay within the selected diameter tolerance.

Geometric comparison

245/35 R19 stays within the configured tolerance for 225/55 R16: 0.0% diameter and 0.0% speedometer effect.

Geometric comparison
Metric This size: 225/55 R16 Alternative: 245/35 R19 Difference Verdict
Overall diameter 25.74 in 25.75 in 0.0% Within tolerance
Section width 8.86 in 9.65 in +0.79 in Computed difference
Sidewall height 4.87 in 3.38 in -1.50 in Computed difference
Circumference 80.88 in 80.90 in 0.0% Within tolerance
Speedo 0.0% 0.0% 0.0% Within tolerance

Seasonal check

Planning a long summer drive?

Use the budget and running-cost tools before a trip, especially if the current tires are worn or the replacement size changes diameter.

Estimate tire budget

What this geometry means

225/55 R16 has a mid-range sidewall proportion. The marking combines nominal section width 8.86 in, sidewall ratio 55% and rim diameter 16 inches. One sidewall is 4.87 in; both sidewalls make up 38% of the 25.74 in overall diameter, while the rim makes up 62%.

At the nominal 80.88 in circumference, 1,000 rotations cover 2.05 km (1.28 mi); the inverse rates are 487/km and 783/mi.

Section-width mix versus 225/55 R16: 4 narrower, 2 equal-width and 6 wider entries.

The closest diameter entry is 245/35 R19 at +0.0%. Relative to 225/55 R16, it changes nominal section width by +0.79 in, each sidewall by -1.50 in and radius by +0.00 in.

Curated alternatives: 12 sizes, spanning -1.3% to +1.1% in nominal diameter versus 225/55 R16.

Width endpoints in that set are 205/60 R16 (-0.79 in) and 255/35 R19 (+1.18 in) relative to 225/55 R16.

This is a nominal geometry comparison only. Vehicle clearance, wheel width and offset, load and speed ratings, and manufacturer approval still require separate checks.

Specification

Specification
Overall diameter 25.74 in
Section width 8.86 in
Sidewall height 4.87 in
Circumference 80.88 in
Revolutions 487 /km · 783 /mi

In-tolerance sizes

Alternative sizes that stay within the selected diameter tolerance:

In-tolerance sizes
Size Diameter Speedo Verdict
245/35 R19 +0.0% +0.0% ✓ OK
245/40 R18 -0.1% -0.1% ✓ OK
205/60 R16 -0.2% -0.2% ✓ OK
245/45 R17 -0.2% -0.2% ✓ OK
225/50 R17 +0.4% +0.4% ✓ OK
205/55 R17 +0.5% +0.5% ✓ OK
225/45 R18 +0.9% +0.9% ✓ OK
205/65 R15 -1.0% -1.0% ✓ OK
235/35 R19 -1.0% -1.0% ✓ OK
215/50 R17 -1.1% -1.1% ✓ OK
255/35 R19 +1.1% +1.1% ✓ OK
235/40 R18 -1.3% -1.3% ✓ OK

Compare sizes

Looks valid
Looks valid
Units
High fitment riskWithin tolerance · Diameter +0.0% (+0.01 in) · US (~3%)
  • High fitment risk · This rating covers tire geometry only, not vehicle compatibility.
  • Diameter +0.0% · Ride-height change +0.00 in.
  • Speedometer unchanged · 60 mph → 60.0 mph.
  • Sidewall -1.50 in · Width +0.79 in.
Diameter+0.0%+0.01 in
Speedo @ 60+0.0%60 mph → 60.0 mph
Sidewall-1.50 inWidth +0.79 in
Ride-height change+0.00 inDiameter ÷ 2
How this result is calculated

Computed from nominal tire-size geometry: diameter, circumference and speedometer error. It does not check vehicle placard approval, load/speed rating, rim-width range, wheel-arch, suspension or brake clearance.

Methodology

Before fitting

  • Check the vehicle placard and owner’s manual first.
  • Match or exceed the required load index and speed rating.
  • Confirm rim-width range, bolt pattern, hub bore, offset and fasteners.
  • Inspect wheel-arch, suspension and brake clearance under real vehicle load.
  • Check TPMS, cold pressure and local roadworthiness rules.
Diameter
25.74 in 25.75 in+0.01 in
Sidewall
4.87 in 3.38 in-1.50 in
Width
8.86 in 9.65 in+0.79 in
Circumference
80.88 in 80.90 in+0.0%
Revs / mile
783 783
Speedo @ 60
60 mph 60.0 mph+0.0%
Ride-height change
0.00 in +0.00 in
True distance per 100 indicated
100 mi 100.0 mi+0.0%
Δ⌀ +0.01 inΔ↔ +0.79 in
  • Current — 225/55 R16
  • New — 245/35 R19
  • Grounded to the road: the axle rises +0.00 in.

Result report

225/55 R16 245/35 R19 · High fitment risk · Within tolerance

Copy/print uses this page state only; TireFitLab does not create an account or store a server-side report.

Embed or cite this result
Open embed preview

Geometric estimate. Always verify physical clearance (arches, suspension, brakes) before fitting.

In-tolerance alternative sizes

In-tolerance alternative sizes
SizeDiameterSpeedo @ 100Use this
−1″ 195/70R15+0.0%+0.0%
OE 225/55R16+0.0%+0.0%

More tools

Last reviewed: 2026-07-22

Technical check
2026-07-22
Content updated
2026-07-22
What changed
  • Added a localized engine-derived geometry signature and matching Markdown narrative.
Methodology