TireFitLab

285/35 R22

What size is 285/35 R22?

285/35 R22 has an overall diameter of about 29.85 in, a section width of 11.22 in and a sidewall height of 3.93 in. It turns roughly 676 times per mile. Below are the exact figures plus plus/minus sizes that stay within the selected diameter tolerance.

Geometric comparison

235/70 R17 stays within the configured tolerance for 285/35 R22: +0.3% diameter and +0.3% speedometer effect.

Geometric comparison
Metric This size: 285/35 R22 Alternative: 235/70 R17 Difference Verdict
Overall diameter 29.85 in 29.95 in +0.3% Within tolerance
Section width 11.22 in 9.25 in -1.97 in Computed difference
Sidewall height 3.93 in 6.48 in +2.55 in Computed difference
Circumference 93.79 in 94.10 in +0.3% Within tolerance
Speedo 0.0% +0.3% +0.3% Within tolerance

Seasonal check

Planning a long summer drive?

Use the budget and running-cost tools before a trip, especially if the current tires are worn or the replacement size changes diameter.

Estimate tire budget

What this geometry means

285/35 R22 has a low-profile proportion. The marking combines nominal section width 11.22 in, sidewall ratio 35% and rim diameter 22 inches. One sidewall is 3.93 in; both sidewalls make up 26% of the 29.85 in overall diameter, while the rim makes up 74%.

The closest diameter entry is 235/70 R17 at +0.3%. Relative to 285/35 R22, it changes nominal section width by -1.97 in, each sidewall by +2.55 in and radius by +0.05 in.

At the nominal 93.79 in circumference, 1,000 rotations cover 2.38 km (1.48 mi); the inverse rates are 420/km and 676/mi.

Width endpoints in that set are 235/70 R17 (-1.97 in) and 305/40 R20 (+0.79 in) relative to 285/35 R22.

Curated alternatives: 12 sizes, spanning -1.6% to +1.6% in nominal diameter versus 285/35 R22.

Section-width mix versus 285/35 R22: 11 narrower, 0 equal-width and 1 wider entries.

This is a nominal geometry comparison only. Vehicle clearance, wheel width and offset, load and speed ratings, and manufacturer approval still require separate checks.

Specification

Specification
Overall diameter 29.85 in
Section width 11.22 in
Sidewall height 3.93 in
Circumference 93.79 in
Revolutions 420 /km · 676 /mi

In-tolerance sizes

Alternative sizes that stay within the selected diameter tolerance:

In-tolerance sizes
Size Diameter Speedo Verdict
235/70 R17 +0.3% +0.3% ✓ OK
275/45 R20 -0.4% -0.4% ✓ OK
235/65 R18 +0.6% +0.6% ✓ OK
255/50 R20 +0.6% +0.6% ✓ OK
255/65 R17 +0.7% +0.7% ✓ OK
305/40 R20 -0.8% -0.8% ✓ OK
245/60 R18 -0.9% -0.9% ✓ OK
245/65 R17 -1.1% -1.1% ✓ OK
245/70 R16 -1.2% -1.2% ✓ OK
265/50 R19 -1.4% -1.4% ✓ OK
265/45 R20 -1.6% -1.6% ✓ OK
265/40 R22 +1.6% +1.6% ✓ OK

Compare sizes

Looks valid
Looks valid
Units
Not recommendedWithin tolerance · Diameter +0.3% (+0.10 in) · US (~3%)
  • Not recommended · This rating covers tire geometry only, not vehicle compatibility.
  • Diameter +0.3% · Ride-height change +0.05 in.
  • Speedometer reads low · 60 mph → 60.2 mph.
  • Sidewall +2.55 in · Width -1.97 in.
Diameter+0.3%+0.10 in
Speedo @ 60+0.3%60 mph → 60.2 mph
Sidewall+2.55 inWidth -1.97 in
Ride-height change+0.05 inDiameter ÷ 2
How this result is calculated

Computed from nominal tire-size geometry: diameter, circumference and speedometer error. It does not check vehicle placard approval, load/speed rating, rim-width range, wheel-arch, suspension or brake clearance.

Methodology

Before fitting

  • Check the vehicle placard and owner’s manual first.
  • Match or exceed the required load index and speed rating.
  • Confirm rim-width range, bolt pattern, hub bore, offset and fasteners.
  • Inspect wheel-arch, suspension and brake clearance under real vehicle load.
  • Check TPMS, cold pressure and local roadworthiness rules.
Diameter
29.85 in 29.95 in+0.10 in
Sidewall
3.93 in 6.48 in+2.55 in
Width
11.22 in 9.25 in-1.97 in
Circumference
93.79 in 94.10 in+0.3%
Revs / mile
676 673
Speedo @ 60
60 mph 60.2 mph+0.3%
Ride-height change
0.00 in +0.05 in
True distance per 100 indicated
100 mi 100.3 mi+0.3%
Δ⌀ +0.10 inΔ↔ -1.97 in
  • Current — 285/35 R22
  • New — 235/70 R17
  • Grounded to the road: the axle rises +0.05 in.

Result report

285/35 R22 235/70 R17 · Not recommended · Within tolerance

Copy/print uses this page state only; TireFitLab does not create an account or store a server-side report.

Embed or cite this result
Open embed preview

Geometric estimate. Always verify physical clearance (arches, suspension, brakes) before fitting.

In-tolerance alternative sizes

In-tolerance alternative sizes
SizeDiameterSpeedo @ 100Use this
OE 285/35R22+0.0%+0.0%

More tools

Last reviewed: 2026-07-22

Technical check
2026-07-22
Content updated
2026-07-22
What changed
  • Added a localized engine-derived geometry signature and matching Markdown narrative.
Methodology