TireFitLab

295/35 R21

What size is 295/35 R21?

295/35 R21 has an overall diameter of about 29.13 in, a section width of 11.61 in and a sidewall height of 4.06 in. It turns roughly 692 times per mile. Below are the exact figures plus plus/minus sizes that stay within the selected diameter tolerance.

Geometric comparison

235/60 R18 stays within the configured tolerance for 295/35 R21: -0.1% diameter and -0.1% speedometer effect.

Geometric comparison
Metric This size: 295/35 R21 Alternative: 235/60 R18 Difference Verdict
Overall diameter 29.13 in 29.10 in -0.1% Within tolerance
Section width 11.61 in 9.25 in -2.36 in Computed difference
Sidewall height 4.06 in 5.55 in +1.49 in Computed difference
Circumference 91.51 in 91.43 in -0.1% Within tolerance
Speedo 0.0% -0.1% -0.1% Within tolerance

Seasonal check

Planning a long summer drive?

Use the budget and running-cost tools before a trip, especially if the current tires are worn or the replacement size changes diameter.

Estimate tire budget

What this geometry means

295/35 R21 has a low-profile proportion. The marking combines nominal section width 11.61 in, sidewall ratio 35% and rim diameter 21 inches. One sidewall is 4.06 in; both sidewalls make up 28% of the 29.13 in overall diameter, while the rim makes up 72%.

The closest diameter entry is 235/60 R18 at -0.1%. Relative to 295/35 R21, it changes nominal section width by -2.36 in, each sidewall by +1.49 in and radius by -0.01 in.

At the nominal 91.51 in circumference, 1,000 rotations cover 2.32 km (1.44 mi); the inverse rates are 430/km and 692/mi.

Width endpoints in that set are 235/60 R18 (-2.36 in) and 295/40 R20 (+0.00 in) relative to 295/35 R21.

Curated alternatives: 12 sizes, spanning -1.3% to +1.3% in nominal diameter versus 295/35 R21.

Section-width mix versus 295/35 R21: 11 narrower, 1 equal-width and 0 wider entries.

This is a nominal geometry comparison only. Vehicle clearance, wheel width and offset, load and speed ratings, and manufacturer approval still require separate checks.

Specification

Specification
Overall diameter 29.13 in
Section width 11.61 in
Sidewall height 4.06 in
Circumference 91.51 in
Revolutions 430 /km · 692 /mi

In-tolerance sizes

Alternative sizes that stay within the selected diameter tolerance:

In-tolerance sizes
Size Diameter Speedo Verdict
235/60 R18 -0.1% -0.1% ✓ OK
285/45 R19 -0.1% -0.1% ✓ OK
235/55 R19 +0.2% +0.2% ✓ OK
255/55 R18 -0.3% -0.3% ✓ OK
255/50 R19 -0.3% -0.3% ✓ OK
255/45 R20 -0.3% -0.3% ✓ OK
235/65 R17 -0.4% -0.4% ✓ OK
295/40 R20 +0.6% +0.6% ✓ OK
265/45 R20 +0.9% +0.9% ✓ OK
265/50 R19 +1.0% +1.0% ✓ OK
245/70 R16 +1.3% +1.3% ✓ OK
275/45 R19 -1.3% -1.3% ✓ OK

Compare sizes

Looks valid
Looks valid
Units
Not recommendedWithin tolerance · Diameter -0.1% (-0.03 in) · US (~3%)
  • Not recommended · This rating covers tire geometry only, not vehicle compatibility.
  • Diameter -0.1% · Ride-height change -0.01 in.
  • Speedometer reads high · 60 mph → 59.9 mph.
  • Sidewall +1.49 in · Width -2.36 in.
Diameter-0.1%-0.03 in
Speedo @ 60-0.1%60 mph → 59.9 mph
Sidewall+1.49 inWidth -2.36 in
Ride-height change-0.01 inDiameter ÷ 2
How this result is calculated

Computed from nominal tire-size geometry: diameter, circumference and speedometer error. It does not check vehicle placard approval, load/speed rating, rim-width range, wheel-arch, suspension or brake clearance.

Methodology

Before fitting

  • Check the vehicle placard and owner’s manual first.
  • Match or exceed the required load index and speed rating.
  • Confirm rim-width range, bolt pattern, hub bore, offset and fasteners.
  • Inspect wheel-arch, suspension and brake clearance under real vehicle load.
  • Check TPMS, cold pressure and local roadworthiness rules.
Diameter
29.13 in 29.10 in-0.03 in
Sidewall
4.06 in 5.55 in+1.49 in
Width
11.61 in 9.25 in-2.36 in
Circumference
91.51 in 91.43 in-0.1%
Revs / mile
692 693
Speedo @ 60
60 mph 59.9 mph-0.1%
Ride-height change
0.00 in -0.01 in
True distance per 100 indicated
100 mi 99.9 mi-0.1%
Δ⌀ -0.03 inΔ↔ -2.36 in
  • Current — 295/35 R21
  • New — 235/60 R18
  • Grounded to the road: the axle rises -0.01 in.

Result report

295/35 R21 235/60 R18 · Not recommended · Within tolerance

Copy/print uses this page state only; TireFitLab does not create an account or store a server-side report.

Embed or cite this result
Open embed preview

Geometric estimate. Always verify physical clearance (arches, suspension, brakes) before fitting.

In-tolerance alternative sizes

In-tolerance alternative sizes
SizeDiameterSpeedo @ 100Use this
OE 295/35R21+0.0%+0.0%

More tools

Last reviewed: 2026-07-22

Technical check
2026-07-22
Content updated
2026-07-22
What changed
  • Added a localized engine-derived geometry signature and matching Markdown narrative.
Methodology